- X plane 10 aircraft list how to#
- X plane 10 aircraft list install#
- X plane 10 aircraft list manual#
- X plane 10 aircraft list archive#
- X plane 10 aircraft list full#
Sim/aircraft/forcefeedback/acf_ff_stickshakerīusses that can feed the essential bus. Sim/aircraft/forcefeedback/acf_ff_hydraulic Position of door relative to CG, longitude offset in meters Position of door relative to CG, vertical offset in meters Position of door relative to CG, latitude offset in meters ICAO code for aircraft (a string) entered by author
X plane 10 aircraft list how to#
The yaw string, that thing that no one knows how to get rid of. Maximum structural cruising speed, not to be exceeded except in smooth air
X plane 10 aircraft list full#
Vfe describes the aircrafts max speed with full flaps extended.
Position of pilot's head relative to CG, Z Position of pilot's head relative to CG, Y Position of pilot's head relative to CG, X This is also known as the ADS-B "hexcode".īrief description of the plane. Whether the autopilot is strictly single axis (bank) only.Īttitude source for the autopilot: 10 = AHRS, 11 = elec gyro, 12 = vacuum gyro, 13 = turn coordinator and absolute pressure transducerĭirectional gyro source for the autopilot: 10 = AHRS, 11 = elec gyro (HSI or DG), 12 = vacuum gyro (DG)Ģ4bit (0-16777215 or 0-0xFFFFFF) unique ID of the airframe. Sim/aircraft/autopilot/single_axis_autopilot Sim/aircraft/autopilot/preconfigured_ap_typeĠ=X-Plane custom, 1=Airliner, 2=GFC-700, 3=S-Tec 55, 4=S-Tec 55 with altitude preselect, 5=KAP-140 single axis, 6=KAP-140 dual axis, 7=KAP-140 dual axis with altitude preselect, 8=Piper Autocontrol, 9=Rockwell/Collins FCS-65 Step increment for radio altimeter decision height param file for your aircraft, if you have one available.įor the Vee-gull 005 model, the vee-gull 005.param file is in ArduPilot\Tools\autotest\default_params.Sim/aircraft/autopilot/radio_altimeter_step_ft The parameters can be set via Mission Planner either individually or by loading a. This step needs to be done only the first time you run SITL after (re-)building ArduPlane. Set ArduPilot’s parameters for the chosen RC sailplane. This is normal and won’t happen after you load a. The first time you establish a connection between Mission Planner and ArduPlane SITL after building ArduPlane, before you load ArduPlane parameters as described in the next step, your X-Plane RC plane (which is presumably on the ground when the connection is established) may flip over and crash or otherwise behave strangely. To enter this information, start X-Plane, and once X-Plane has loaded an aircraft hover the pointer near the top of the X-Plane window, click on Settings, choose Net Connections.
X-Plane needs to be told about the IP addresses/ports where it can send data to and receive it from ArduPilot, as well as about the kinds data X-Plane and ArduPilot should exchange. This will enable you to fly, at the very least, Vee-gull 005 and Houston Hawk.Ĭonfigure X-Plane for communicating with ArduPilot.
X plane 10 aircraft list archive#
afl files from the downloaded archive into %XPlane-install-dir%\Airfoils. Originally, this archive comes from a post on X-Plane forum, and this X-Plane forum thread is a good place to look for more airfoils. The airfoils are in NACA_64_xxx_Airfoils_from_TR824.zip in the ArduPilot repo. Fortunately, someone has created and published the airfoils too! Unfortunately, the X-Plane 10 demo doesn’t provide airfoils for most of the above models, and refuses to load these models without them. Extra info on sailplane model installation is here.
X plane 10 aircraft list install#
To install them, create a folder RC Sailplanes under %XPlane-install-dir%\Aircraft and extract the. For more info on joystick calibration in X-Plane, please refer to the Setup of X-Plane 10. You can do so in Windows (on Windows 10: Start menu -> Settings -> Devices -> Printers and Scanners -> Devices and Printers) or in X-Plane (start X-Plane, hover near the top of the X-Plane window, and in the toolbar at that appears at the top of the window go to Settings -> Joystick & Equipment). The Taranis will stay on without using its battery – it is now getting power from the PC.Ĭalibrate it (this needs to be done only the first time you use it as your joystick). Switch on the Taranis, connect it to your PC with a mini USB cable, and move its On-Off switch to Off. To use an FrSky Taranis as an X-Plane joystick: However, several transmitters for RC aircraft, e.g., FrSky Taranis, can also be used as joysticks for X-Plane. X-Plane requires a joystick for manually controlling yaw, pitch, and roll.
X plane 10 aircraft list manual#
The demo version will prevent you from controlling the plane manually after 15 minutes of flying or so, but flying in ArduPlane modes that don’t require manual input, e.g., Auto, and switching modes from a ground control station such as Mission Planner will work even after that.Ĭonfigure a joystick/transmitter for use with X-Plane.
0 kommentar(er)
